AUTO-INSTALLATIONCe fichier a été automatiquement installé dans le cadre d’une mise à jour récente. Si vous rencontrez des problèmes, vous pouvez le télécharger et le réinstaller manuellement.
Le contenu de cette page a peut-être été traduit automatiquement. Pour faire part de vos commentaires, remplissez le formulaire au bas de la page.
Ce fichier a été automatiquement installé dans le cadre d’une mise à jour récente. Si vous rencontrez des problèmes, vous pouvez le télécharger et le réinstaller manuellement.
This package provides the Dell SAS 5/iR Adapter Driver and is supported on the Enterprise Servers and Powervault models that are running the following Operating Systems: Red Hat Enterprise Linux 5 and Novell - SuSE Linux ES 10.
Format de fichier :Un fichier Tar pour l'installation de logiciels
Nom du fichier :mptlinux-4.00.00.01-4dkms_ir.tar.gz
Taille du fichier :1.93 MB
Description du format
Ce fichier est une archive de fichiers compressés pour l’installation de logiciels.
Afin de garantir l’intégrité de votre téléchargement, veuillez vérifier la valeur de la somme de contrôle.
MD5 :
610a1482f1689bf91b1d9f8d1a8f86d1
SHA1 :
Non disponible
SHA-256 :
Non disponible
Connectez-vous à Windows en tant qu’administrateur pour utiliser les fonctionnalités d’analyse automatique. Si vous êtes déjà connecté en tant qu’administrateur et que vous voyez ce message, redémarrez.Votre système est géré par votre administrateur IT et peut avoir des fonctionnalités limitées.
Trouver d’autres mises à jour. Utilisez SupportAssist pour trouver toutes les dernières mises à jour de pilotes disponibles pour votre appareil.
Correctifs et améliorations
Fixes - Fixed several issues in the rpm spec file. - Fixed issue in RHEL5 where removing the secondary disk in an IM array would cause the filesystem to go read-only.
Dell Technologies recommande d’effectuer cette mise à jour au cours du prochain cycle de mise à jour planifié. La mise à jour contient des modifications permettant de maintenir l’intégrité globale du système. Elle garantit que le logiciel du système reste à jour et compatible avec d’autres modules système (firmware, BIOS, pilotes et logiciels) et peut inclure d’autres nouvelles fonctionnalités.
The package is a compressed tar file. To extract the components within the tar file, please follow the instructions as below:
Preparation of the DUD image. 1. From the support site download the file. 2. Transfer the file to a Linux system. 3. Run "gunzip on the transferred file to unzip the file. 4. Run "tar -xvf *.tar" on the unzipped file. 5. Go into the appropriate sub-directory. 6. Transfer the image to the floppy. Use "dd if= of=/dev/fd0" On most systems, the floppy drive is designated by the /dev/fd0 special file.
The RPM package. One of the components of the tar file is an RPM package with a filename ending in .rpm.
3.2 Installing the OS on a SAS 5 controller. -------------------------------------------
Use the command "Linux dd updates" at the beginning of the Linux installation process if you will be installing the O/S to a disk attached to the SAS 5 controller. This step is required because LSI PCI Ids are not in the kernel's supported device table. This work around will always be necessary for these kernels since they are pre-existing and cannot be patched.
Detailed Steps: 1. You will be prompted with "Do you have a driver disk?" 2. Select "Yes" 3. You will be prompted to select the device from which to install drivers. Select fd0 4. You will be prompted to press OK after inserting the driver disk. Select "OK" 5. You will be prompted to load any more drivers. Select "No" 6. Continue with installation.
3.3 Adding the SAS 5 Driver to an Existing Linux system -------------------------------------------------------
1. Install the DKMS rpm package. Use the command "rpm -ivh " 2. Install the Driver package. Use the command "rpm -ivh " 3. Restart the computer for the changes to take effect.
3.4 Updating the SAS 5 Driver on an Existing Linux system. ---------------------------------------------------------
1. If DKMS installation is needed, use the following instruction to install the package. Install the DKMS rpm package. Use the command "rpm -ivh " 2. Install the Driver package. Use the command "rpm -Uvh " 3. Restart the computer for the changes to take effect. 4. When upgrading from an older to newer version of the driver, first uninstall the older RPM doing: # rpm -e mptlinux-- Then install the new rpm doing: # rpm -ivh mptlinux--..rpm